These air operated pumps are used to deliver motor oils, gear oils, hydraulic oils and automatic transmission fluid (ATF) from origial refinery drums or tanks. They are ideal for local or remote installations where oil is piped to multiple hose outlets and/or reels, metered outlets or portable service stations.
These rugged weatherproof units are available in Standard Duty, RAM, and Heavy Duty to meet any pumping requirement. Models for use on 16 gallon drums mount to drum covers. 55-gallon drum models are available with bung adapters, which screw directly into 2" bung holes on drums and covers. Stub pumps are available for use in standard size and bulk tanks equipped with 2" bung opening.
The chart below lists general medium-pressure pump selection guidelihnes. Each application varies and should be carefully considered for special conditions that may require a pump selection other than the standard recommendations listed.
These conditions include, but are not limited to: * Viscosity of product pumped * Ambient temperature conditions * Simultaneous operation of several dispensing outlets * Dispensing volum requirements
When measuring total pump distance, the hose length of dispensing reels should be included in total distance. Pump distance (feet) Up to 10 ft. Up to 25 ft. Up to 75 ft. 75-200 ft. Up to 200 ft. Over 200 ft. Over 300 ft. Number of outlets 1 1 1-2 1-3 3+ 1-3 3+ 16 gallon container N/A 9960-A 9960-A N/A N/A N/A N/A 55 gallon container (all rquire downtubes except 7216-4 and 9969-B) 7216-4*** 9918-A 9918-A*, 9969-B** 9969-B*, 9970** 7783-A4 9970* or 7783-A4** 7793-A1 Bulk container (these pumps require a downtube) 9916-A1 N/A 9918-A*, 9968**, 8568-A4 9968* or 9970** 7783-C4 7783-C4** 7793-C Tubing recommendation (hydraulic fitting) 5/8" OD 0.035" Wall 5/8" OD 0.035" Wall 5/8" OD 0.035" Wall 5/8" OD 0.035" Wall 1" OD 0.049" Wall 1" OD 0.049" Wall 1" OD 0.049" Wall * High volume transfer pump
** For pumping light fluids, e.g., ATF or hydraulic oil
*** For pumping heavy fluids, E.G., 10w 40 and gear oils
NOTE: For pumping Washer Fluid or 50/50 mix of Antifreeze and Water, use 8202 or 7880-C1 regardless of pumping deistance & number of outlets. For pumping non-petroleum based products, contact Alemite Tech Service.
WARNING: Do not operate pump at higher pressure than lowest rated part of system. Sever injury may result if pump is operated at pressures greater than the lowest rated compononent in the distsribution system.
Products New Products Lubrication Fittings Grease Guns Pumps Centralized Lubrication Systems Reels Control Valves and Meters Compressed Air Components Fluid Management Used Fluid Handling Equipment Lubrication Accessories Bulk Oil Systems Quick Links How to Buy Product Literature and Service Sheets
Built for continuous duty, Alemite Industrial Pumps are designed to deliver fluids through long delivery lines or to multiple dispensing points. Pumps are equipped with hoist eyebolts.
SPECIFICATIONS: * Air inlet and outlet: 3/4" NPTF(f) * Material outlet: 1/2" NPTF(f) * 7783 series air motor diameter: 4-1/4" * 7793 series air motor diameter: 6" * Pumps 7783-C4 and 7793-C must have appropriate downtube added * Stub versions have 1-1/2" NPTF(f) inlet
FEATURES: * Recommended for pumping distances over 100 ft. * Included Items: Air Connector, Quick-detach Air Coupler
