DIGITAL INTERVAL TIMER 5 MIN.-12 HR. W/SCROLL-UP
NSI / Tork Electrical, Lighting Pool & Spa Products and Replacement Parts
TIMERS
SSA SERIES SSA100
DIGITAL ELITE TIMERS SSA200
8 TIMERS IN ONE!
SSA200R-24
APPLICATIONS: SSA100 AND SSA200
For energy savings to control lighting or motor loads where an occupancy sensor is not suitable.
Fluorescent and incandescent lighting in areas such as ofces, meeting rooms, library aisles,
stock rooms, equipment rooms.
Timed override of lighting and HVAC for after hours cleaning crews.
Exhaust fans in work areas, utility rooms, bathrooms.
Hot tub heaters and circulating pumps.
Timed override of loads controlled by electromechanical or digital time switches.
APPLICATIONS: SSA200R-24
Interfaces with low voltage HVAC and lighting control systems.
Switches 20 Amp uorescent and incandescent lighting when operated with TORK
TRP transformer relay powerpacks.
Provides switching for loads controlled by BAS/EMS building management systems.
Provides timed override of lighting and HVAC for after hours use.
and
MEETS Can be overridden ON or OFF from remote locations using simple momentary switches.
CALIFORNIA
ENERGY COMMISSIONS ASHRAE
TITLE 24 REQUIREMENTS 90.1 1999
MEETS ADA GUIDELINES CAN INTERFACE WITH LOW VOLTAGE SYSTEMS
FOR CONTROLS &
MECHANISMS 4.27.4 REMOTE OVERRIDE VIA SIMPLE PUSHBUTTONS
FEATURES: ALL SSA MODELS before time out (either or both can be disabled).
Liquid Crystal Display stands out strongly in lighted areas See specications below for details.
and is electroluminescent backlit for dark areas. No minimum load required.
Tamper resistant time-on interval can be preset. In addition, a White decorator type face with matching wallplate
manual scroll-up mode (in 10 minute intervals) can override included.
the dip switch setting temporarily this feature can be dis-
abled, providing a xed interval timer. SSA100, SSA200 ALSO FEATURE:
In addition to numerical read-out LCD displays 10 bars at Zero Power switching prolongs life of relay contacts by
start of time on period. As interval counts down, one bar switching high inrush equipment at or close to zero power.
at a time turns off in 10% decrements. Compatible with electronic ballasts, incandescent lighting,
Flicker of lights and/or beep warning begins 2 minutes or motor loads.
EASY INSTALLATION One simple pushbutton on the face can then do the following:
Easy installation; ts standard 212 wallbox.
Easily replaces wall switch in existing installation.
For use in single or multi-gang applications. 1 Push momentarily and the load comes on for the preset
interval.
White decorator wallplate included.
DIP SWITCH # 1 2 3
5 MIN
DIP SWITCH # 4 5 6
FLICKER ON
At the time of installation, 2 Push momentarily while the load is on and it will turn
off.
15 MIN DIP SWITCH # FLICKER OFF a preset time-on interval
30 MIN 1 2 3 4 5 6 BEEPER ON
and other features are
3 Hold thethe timer resets for 1 or 2original preset interval. is
pushbutton in seconds while the load
1 HR BEEPER OFF
3 HR SCROLL ON selected using a set of dip
6 HR 1 2 3 4 5 6
SCROLL OFF switches. on and up to its
9 HR
12 HR
4 Hold the pushbutton in 10 minutes to its maximum setting.
begins to scroll up from
for over 3 seconds and the timer
NOTE: This feature can be disabled using a tamper resistant dip switch,
providing a xed interval timer. Timing on this chart (above) is for
SSA100 Unit.
32 A DIVISION OF NSi INDUSTRIES, LLC
TIMERS
SSA SERIES SSA100
DIGITAL ELITE TIMERS SSA200
8 TIMERS IN ONE!
SSA200R-24
APPLICATIONS: SSA100 AND SSA200
For energy savings to control lighting or motor loads where an occupancy sensor is not suitable.
Fluorescent and incandescent lighting in areas such as ofces, meeting rooms, library aisles,
stock rooms, equipment rooms.
Timed override of lighting and HVAC for after hours cleaning crews.
Exhaust fans in work areas, utility rooms, bathrooms.
Hot tub heaters and circulating pumps.
Timed override of loads controlled by electromechanical or digital time switches.
APPLICATIONS: SSA200R-24
Interfaces with low voltage HVAC and lighting control systems.
Switches 20 Amp uorescent and incandescent lighting when operated with TORK
TRP transformer relay powerpacks.
Provides switching for loads controlled by BAS/EMS building management systems.
Provides timed override of lighting and HVAC for after hours use.
and
MEETS Can be overridden ON or OFF from remote locations using simple momentary switches.
CALIFORNIA
ENERGY COMMISSIONS ASHRAE
TITLE 24 REQUIREMENTS 90.1 1999
MEETS ADA GUIDELINES CAN INTERFACE WITH LOW VOLTAGE SYSTEMS
FOR CONTROLS &
MECHANISMS 4.27.4 REMOTE OVERRIDE VIA SIMPLE PUSHBUTTONS
FEATURES: ALL SSA MODELS before time out (either or both can be disabled).
Liquid Crystal Display stands out strongly in lighted areas See specications below for details.
and is electroluminescent backlit for dark areas. No minimum load required.
Tamper resistant time-on interval can be preset. In addition, a White decorator type face with matching wallplate
manual scroll-up mode (in 10 minute intervals) can override included.
the dip switch setting temporarily this feature can be dis-
abled, providing a xed interval timer. SSA100, SSA200 ALSO FEATURE:
In addition to numerical read-out LCD displays 10 bars at Zero Power switching prolongs life of relay contacts by
start of time on period. As interval counts down, one bar switching high inrush equipment at or close to zero power.
at a time turns off in 10% decrements. Compatible with electronic ballasts, incandescent lighting,
Flicker of lights and/or beep warning begins 2 minutes or motor loads.
EASY INSTALLATION One simple pushbutton on the face can then do the following:
Easy installation; ts standard 212 wallbox.
Easily replaces wall switch in existing installation.
For use in single or multi-gang applications. 1 Push momentarily and the load comes on for the preset
interval.
White decorator wallplate included.
DIP SWITCH # 1 2 3
5 MIN
DIP SWITCH # 4 5 6
FLICKER ON
At the time of installation, 2 Push momentarily while the load is on and it will turn
off.
15 MIN DIP SWITCH # FLICKER OFF a preset time-on interval
30 MIN 1 2 3 4 5 6 BEEPER ON
and other features are
3 Hold thethe timer resets for 1 or 2original preset interval. is
pushbutton in seconds while the load
1 HR BEEPER OFF
3 HR SCROLL ON selected using a set of dip
6 HR 1 2 3 4 5 6
SCROLL OFF switches. on and up to its
9 HR
12 HR
4 Hold the pushbutton in 10 minutes to its maximum setting.
begins to scroll up from
for over 3 seconds and the timer
NOTE: This feature can be disabled using a tamper resistant dip switch,
providing a xed interval timer. Timing on this chart (above) is for
SSA100 Unit.
32 A DIVISION OF NSi INDUSTRIES, LLC
TIMERS
SSA SERIES SSA100
DIGITAL ELITE TIMERS SSA200
8 TIMERS IN ONE!
SSA200R-24
APPLICATIONS: SSA100 AND SSA200
For energy savings to control lighting or motor loads where an occupancy sensor is not suitable.
Fluorescent and incandescent lighting in areas such as ofces, meeting rooms, library aisles,
stock rooms, equipment rooms.
Timed override of lighting and HVAC for after hours cleaning crews.
Exhaust fans in work areas, utility rooms, bathrooms.
Hot tub heaters and circulating pumps.
Timed override of loads controlled by electromechanical or digital time switches.
APPLICATIONS: SSA200R-24
Interfaces with low voltage HVAC and lighting control systems.
Switches 20 Amp uorescent and incandescent lighting when operated with TORK
TRP transformer relay powerpacks.
Provides switching for loads controlled by BAS/EMS building management systems.
Provides timed override of lighting and HVAC for after hours use.
and
MEETS Can be overridden ON or OFF from remote locations using simple momentary switches.
CALIFORNIA
ENERGY COMMISSIONS ASHRAE
TITLE 24 REQUIREMENTS 90.1 1999
MEETS ADA GUIDELINES CAN INTERFACE WITH LOW VOLTAGE SYSTEMS
FOR CONTROLS &
MECHANISMS 4.27.4 REMOTE OVERRIDE VIA SIMPLE PUSHBUTTONS
FEATURES: ALL SSA MODELS before time out (either or both can be disabled).
Liquid Crystal Display stands out strongly in lighted areas See specications below for details.
and is electroluminescent backlit for dark areas. No minimum load required.
Tamper resistant time-on interval can be preset. In addition, a White decorator type face with matching wallplate
manual scroll-up mode (in 10 minute intervals) can override included.
the dip switch setting temporarily this feature can be dis-
abled, providing a xed interval timer. SSA100, SSA200 ALSO FEATURE:
In addition to numerical read-out LCD displays 10 bars at Zero Power switching prolongs life of relay contacts by
start of time on period. As interval counts down, one bar switching high inrush equipment at or close to zero power.
at a time turns off in 10% decrements. Compatible with electronic ballasts, incandescent lighting,
Flicker of lights and/or beep warning begins 2 minutes or motor loads.
EASY INSTALLATION One simple pushbutton on the face can then do the following:
Easy installation; ts standard 212 wallbox.
Easily replaces wall switch in existing installation.
For use in single or multi-gang applications. 1 Push momentarily and the load comes on for the preset
interval.
White decorator wallplate included.
DIP SWITCH # 1 2 3
5 MIN
DIP SWITCH # 4 5 6
FLICKER ON
At the time of installation, 2 Push momentarily while the load is on and it will turn
off.
15 MIN DIP SWITCH # FLICKER OFF a preset time-on interval
30 MIN 1 2 3 4 5 6 BEEPER ON
and other features are
3 Hold thethe timer resets for 1 or 2original preset interval. is
pushbutton in seconds while the load
1 HR BEEPER OFF
3 HR SCROLL ON selected using a set of dip
6 HR 1 2 3 4 5 6
SCROLL OFF switches. on and up to its
9 HR
12 HR
4 Hold the pushbutton in 10 minutes to its maximum setting.
begins to scroll up from
for over 3 seconds and the timer
NOTE: This feature can be disabled using a tamper resistant dip switch,
providing a xed interval timer. Timing on this chart (above) is for
SSA100 Unit.
32 A DIVISION OF NSi INDUSTRIES, LLC
TIMERS
SSA SERIES SSA100
DIGITAL ELITE TIMERS SSA200
8 TIMERS IN ONE!
SSA200R-24
APPLICATIONS: SSA100 AND SSA200
For energy savings to control lighting or motor loads where an occupancy sensor is not suitable.
Fluorescent and incandescent lighting in areas such as ofces, meeting rooms, library aisles,
stock rooms, equipment rooms.
Timed override of lighting and HVAC for after hours cleaning crews.
Exhaust fans in work areas, utility rooms, bathrooms.
Hot tub heaters and circulating pumps.
Timed override of loads controlled by electromechanical or digital time switches.
APPLICATIONS: SSA200R-24
Interfaces with low voltage HVAC and lighting control systems.
Switches 20 Amp uorescent and incandescent lighting when operated with TORK
TRP transformer relay powerpacks.
Provides switching for loads controlled by BAS/EMS building management systems.
Provides timed override of lighting and HVAC for after hours use.
and
MEETS Can be overridden ON or OFF from remote locations using simple momentary switches.
CALIFORNIA
ENERGY COMMISSIONS ASHRAE
TITLE 24 REQUIREMENTS 90.1 1999
MEETS ADA GUIDELINES CAN INTERFACE WITH LOW VOLTAGE SYSTEMS
FOR CONTROLS &
MECHANISMS 4.27.4 REMOTE OVERRIDE VIA SIMPLE PUSHBUTTONS
FEATURES: ALL SSA MODELS before time out (either or both can be disabled).
Liquid Crystal Display stands out strongly in lighted areas See specications below for details.
and is electroluminescent backlit for dark areas. No minimum load required.
Tamper resistant time-on interval can be preset. In addition, a White decorator type face with matching wallplate
manual scroll-up mode (in 10 minute intervals) can override included.
the dip switch setting temporarily this feature can be dis-
abled, providing a xed interval timer. SSA100, SSA200 ALSO FEATURE:
In addition to numerical read-out LCD displays 10 bars at Zero Power switching prolongs life of relay contacts by
start of time on period. As interval counts down, one bar switching high inrush equipment at or close to zero power.
at a time turns off in 10% decrements. Compatible with electronic ballasts, incandescent lighting,
Flicker of lights and/or beep warning begins 2 minutes or motor loads.
EASY INSTALLATION One simple pushbutton on the face can then do the following:
Easy installation; ts standard 212 wallbox.
Easily replaces wall switch in existing installation.
For use in single or multi-gang applications. 1 Push momentarily and the load comes on for the preset
interval.
White decorator wallplate included.
DIP SWITCH # 1 2 3
5 MIN
DIP SWITCH # 4 5 6
FLICKER ON
At the time of installation, 2 Push momentarily while the load is on and it will turn
off.
15 MIN DIP SWITCH # FLICKER OFF a preset time-on interval
30 MIN 1 2 3 4 5 6 BEEPER ON
and other features are
3 Hold thethe timer resets for 1 or 2original preset interval. is
pushbutton in seconds while the load
1 HR BEEPER OFF
3 HR SCROLL ON selected using a set of dip
6 HR 1 2 3 4 5 6
SCROLL OFF switches. on and up to its
9 HR
12 HR
4 Hold the pushbutton in 10 minutes to its maximum setting.
begins to scroll up from
for over 3 seconds and the timer
NOTE: This feature can be disabled using a tamper resistant dip switch,
providing a xed interval timer. Timing on this chart (above) is for
SSA100 Unit.
32 A DIVISION OF NSi INDUSTRIES, LLC
CATALOG UPC
NO CODE SETTABLE INTERVALS
SSA100 14010 MINUTES: 5, 15, 30 HOURS: 1, 3, 6, 9, 12
SSA200 14011 MINUTES: 10, 20, 40, 60, 90 HOURS: 2, 4, 6, 8
SSA200R-24 14014 MINUTES: 10, 20, 40, 60, 90 HOURS: 2, 4, 6, 8
SPECIFICATIONS & WIRING DIAGRAM:
SSA100, SSA200 SSA100/200
Note: unit is not suitable for lamps which require long striking periods
i.e. HID type.
BLACK HOT
INPUT: Multi-voltage 120/277 VAC, 50/60Hz GREEN 120V GROUND
CONTACT RATINGS: GREEN /YELLOW 277V GROUND
type 120VAC 277VAC
tungsten 800W RED LOAD NEUTRAL
ballast 800W 1200W
motor 1/6HP SSA100/200
pilot duty 240VA
TIMING ACCURACY: .002% BLACK HOT
OPERATING TEMPERATURE: 0 - 100 F OPERATING HUMIDITY: 90% RH Non-condensing GREEN 120V GROUND
GREEN /YELLOW 277V GROUND
COLOR of faceplate and wallplate: white RED (+) 24VAC
WARNING BEFORE TIME OUT: Flicker feature turns load off for 1 second, 2 minutes before end of timed RED or
NEUTRAL
LOAD ()
cycle and again 1 minute before end of timed cycle. BLACK VDC
BEEP FEATURE will sound a 12 second beep every 12 seconds during the last 2 minutes of timed cycle.
ORANGE NC
BLUE C
REMOTE GREY
OVERRIDE NO
YELLOW
RED (+) 24VAC
SPECIFICATIONS & WIRING DIAGRAM: YELLOW or
BLACK () VDC
SSA200R-24
INPUT VOLTAGE: 24VAC / VDC (No Minimum Load) SSA200R-24 ORANGE NC
CURRENT DRAW: 16ma max. @ 24VDC BLUE C
USING TRP TRANSFORMER RELAY POWERPACK 20 AMP
22ma max. @ 24VAC REMOTE GREY
LOAD
CONTACTS: Single Pole, Double Throw OVERRIDE NO L
RED
Isolated Contacts YELLOW
RED
RED
CONTACT RATING: 1 A 30V Maximum YELLOW
BLACK
100A @ 1V Minimum RED
ORANGE NC
TORK
TIMING ACCURACY: .002%
TRP
BLUE BLACK
OPERATING TEMPERATURE: 0- 100 F SSA200R-24 C
REMOTE GREY
OPERATING HUMIDITY: 90% RH Non-condensing USINGOVERRIDE
TRP TRANSFORMER NO
RELAY POWERPACK BLUE 20 AMP
COLOR of faceplate and wallplate: white YELLOW LOAD
WHITE
BLACK
RED L
WARNING BEFORE TIME OUT: Flicker feature turns load YELLOW
RED
RED
LOW
off for 1 second, 2 minutes before end of timed cycle BLACK
VOLTAGE N L
and again 1 minute before end of timed cycle. RED
BEEP FEATURE will sound a 12 second beep every 12 ORANGE NC TORK
TRP
BLUE BLACK
seconds during the last 2 minutes of timed cycle. C
REMOTE GREY
OVERRIDE NO BLUE
YELLOW
WHITE
BLACK
YELLOW LOW
VOLTAGE N L
SPECIFICATION WRITERS GUIDE SSA100, SSA200
Furnish and install a solid state interval time switch with backlit LCD display. Intervals can be preset using a series of dip switches. A tamper resistant manual scroll-up mode must
be provided to override the dip switch setting temporarily. Unit shall be capable of a user selectable audible and/or visual warning beginning 2 minutes prior to time out. Unit
design to provide zero power switching for the contacts. Unit to accept 120/277VAC, 50/60 Hz. A white decorator wallplate to be included.
SPECIFICATION WRITERS GUIDE SSA200R-24
Furnish and install a solid state interval time switch with backlit LCD display. Intervals can be preset using a series of dip switches. A tamper resistant manual scroll-up mode must
be provided to override the dip switch setting temporarily. Unit shall be capable of a user selectable audible and/or visual warning beginning 2 minutes prior to time out. Unit to
accept 24VAC/ DC. A white decorator wallplate to be included.
JUNE 2007 A DIVISION OF NSi INDUSTRIES, LLC
33
CATALOG UPC
NO CODE SETTABLE INTERVALS
SSA100 14010 MINUTES: 5, 15, 30 HOURS: 1, 3, 6, 9, 12
SSA200 14011 MINUTES: 10, 20, 40, 60, 90 HOURS: 2, 4, 6, 8
SSA200R-24 14014 MINUTES: 10, 20, 40, 60, 90 HOURS: 2, 4, 6, 8
SPECIFICATIONS & WIRING DIAGRAM:
SSA100, SSA200 SSA100/200
Note: unit is not suitable for lamps which require long striking periods
i.e. HID type.
BLACK HOT
INPUT: Multi-voltage 120/277 VAC, 50/60Hz GREEN 120V GROUND
CONTACT RATINGS: GREEN /YELLOW 277V GROUND
type 120VAC 277VAC
tungsten 800W RED LOAD NEUTRAL
ballast 800W 1200W
motor 1/6HP SSA100/200
pilot duty 240VA
TIMING ACCURACY: .002% BLACK HOT
OPERATING TEMPERATURE: 0 - 100 F OPERATING HUMIDITY: 90% RH Non-condensing GREEN 120V GROUND
GREEN /YELLOW 277V GROUND
COLOR of faceplate and wallplate: white RED (+) 24VAC
WARNING BEFORE TIME OUT: Flicker feature turns load off for 1 second, 2 minutes before end of timed RED or
NEUTRAL
LOAD ()
cycle and again 1 minute before end of timed cycle. BLACK VDC
BEEP FEATURE will sound a 12 second beep every 12 seconds during the last 2 minutes of timed cycle.
ORANGE NC
BLUE C
REMOTE GREY
OVERRIDE NO
YELLOW
RED (+) 24VAC
SPECIFICATIONS & WIRING DIAGRAM: YELLOW or
BLACK () VDC
SSA200R-24
INPUT VOLTAGE: 24VAC / VDC (No Minimum Load) SSA200R-24 ORANGE NC
CURRENT DRAW: 16ma max. @ 24VDC BLUE C
USING TRP TRANSFORMER RELAY POWERPACK 20 AMP
22ma max. @ 24VAC REMOTE GREY
LOAD
CONTACTS: Single Pole, Double Throw OVERRIDE NO L
RED
Isolated Contacts YELLOW
RED
RED
CONTACT RATING: 1 A 30V Maximum YELLOW
BLACK
100A @ 1V Minimum RED
ORANGE NC
TORK
TIMING ACCURACY: .002%
TRP
BLUE BLACK
OPERATING TEMPERATURE: 0- 100 F SSA200R-24 C
REMOTE GREY
OPERATING HUMIDITY: 90% RH Non-condensing USINGOVERRIDE
TRP TRANSFORMER NO
RELAY POWERPACK BLUE 20 AMP
COLOR of faceplate and wallplate: white YELLOW LOAD
WHITE
BLACK
RED L
WARNING BEFORE TIME OUT: Flicker feature turns load YELLOW
RED
RED
LOW
off for 1 second, 2 minutes before end of timed cycle BLACK
VOLTAGE N L
and again 1 minute before end of timed cycle. RED
BEEP FEATURE will sound a 12 second beep every 12 ORANGE NC TORK
TRP
BLUE BLACK
seconds during the last 2 minutes of timed cycle. C
REMOTE GREY
OVERRIDE NO BLUE
YELLOW
WHITE
BLACK
YELLOW LOW
VOLTAGE N L
SPECIFICATION WRITERS GUIDE SSA100, SSA200
Furnish and install a solid state interval time switch with backlit LCD display. Intervals can be preset using a series of dip switches. A tamper resistant manual scroll-up mode must
be provided to override the dip switch setting temporarily. Unit shall be capable of a user selectable audible and/or visual warning beginning 2 minutes prior to time out. Unit
design to provide zero power switching for the contacts. Unit to accept 120/277VAC, 50/60 Hz. A white decorator wallplate to be included.
SPECIFICATION WRITERS GUIDE SSA200R-24
Furnish and install a solid state interval time switch with backlit LCD display. Intervals can be preset using a series of dip switches. A tamper resistant manual scroll-up mode must
be provided to override the dip switch setting temporarily. Unit shall be capable of a user selectable audible and/or visual warning beginning 2 minutes prior to time out. Unit to
accept 24VAC/ DC. A white decorator wallplate to be included.
JUNE 2007 A DIVISION OF NSi INDUSTRIES, LLC
33
CATALOG UPC
NO CODE SETTABLE INTERVALS
SSA100 14010 MINUTES: 5, 15, 30 HOURS: 1, 3, 6, 9, 12
SSA200 14011 MINUTES: 10, 20, 40, 60, 90 HOURS: 2, 4, 6, 8
SSA200R-24 14014 MINUTES: 10, 20, 40, 60, 90 HOURS: 2, 4, 6, 8
SPECIFICATIONS & WIRING DIAGRAM:
SSA100, SSA200 SSA100/200
Note: unit is not suitable for lamps which require long striking periods
i.e. HID type.
BLACK HOT
INPUT: Multi-voltage 120/277 VAC, 50/60Hz GREEN 120V GROUND
CONTACT RATINGS: GREEN /YELLOW 277V GROUND
type 120VAC 277VAC
tungsten 800W RED LOAD NEUTRAL
ballast 800W 1200W
motor 1/6HP SSA100/200
pilot duty 240VA
TIMING ACCURACY: .002% BLACK HOT
OPERATING TEMPERATURE: 0 - 100 F OPERATING HUMIDITY: 90% RH Non-condensing GREEN 120V GROUND
GREEN /YELLOW 277V GROUND
COLOR of faceplate and wallplate: white RED (+) 24VAC
WARNING BEFORE TIME OUT: Flicker feature turns load off for 1 second, 2 minutes before end of timed RED or
NEUTRAL
LOAD ()
cycle and again 1 minute before end of timed cycle. BLACK VDC
BEEP FEATURE will sound a 12 second beep every 12 seconds during the last 2 minutes of timed cycle.
ORANGE NC
BLUE C
REMOTE GREY
OVERRIDE NO
YELLOW
RED (+) 24VAC
SPECIFICATIONS & WIRING DIAGRAM: YELLOW or
BLACK () VDC
SSA200R-24
INPUT VOLTAGE: 24VAC / VDC (No Minimum Load) SSA200R-24 ORANGE NC
CURRENT DRAW: 16ma max. @ 24VDC BLUE C
USING TRP TRANSFORMER RELAY POWERPACK 20 AMP
22ma max. @ 24VAC REMOTE GREY
LOAD
CONTACTS: Single Pole, Double Throw OVERRIDE NO L
RED
Isolated Contacts YELLOW
RED
RED
CONTACT RATING: 1 A 30V Maximum YELLOW
BLACK
100A @ 1V Minimum RED
ORANGE NC
TORK
TIMING ACCURACY: .002%
TRP
BLUE BLACK
OPERATING TEMPERATURE: 0- 100 F SSA200R-24 C
REMOTE GREY
OPERATING HUMIDITY: 90% RH Non-condensing USINGOVERRIDE
TRP TRANSFORMER NO
RELAY POWERPACK BLUE 20 AMP
COLOR of faceplate and wallplate: white YELLOW LOAD
WHITE
BLACK
RED L
WARNING BEFORE TIME OUT: Flicker feature turns load YELLOW
RED
RED
LOW
off for 1 second, 2 minutes before end of timed cycle BLACK
VOLTAGE N L
and again 1 minute before end of timed cycle. RED
BEEP FEATURE will sound a 12 second beep every 12 ORANGE NC TORK
TRP
BLUE BLACK
seconds during the last 2 minutes of timed cycle. C
REMOTE GREY
OVERRIDE NO BLUE
YELLOW
WHITE
BLACK
YELLOW LOW
VOLTAGE N L
SPECIFICATION WRITERS GUIDE SSA100, SSA200
Furnish and install a solid state interval time switch with backlit LCD display. Intervals can be preset using a series of dip switches. A tamper resistant manual scroll-up mode must
be provided to override the dip switch setting temporarily. Unit shall be capable of a user selectable audible and/or visual warning beginning 2 minutes prior to time out. Unit
design to provide zero power switching for the contacts. Unit to accept 120/277VAC, 50/60 Hz. A white decorator wallplate to be included.
SPECIFICATION WRITERS GUIDE SSA200R-24
Furnish and install a solid state interval time switch with backlit LCD display. Intervals can be preset using a series of dip switches. A tamper resistant manual scroll-up mode must
be provided to override the dip switch setting temporarily. Unit shall be capable of a user selectable audible and/or visual warning beginning 2 minutes prior to time out. Unit to
accept 24VAC/ DC. A white decorator wallplate to be included.
JUNE 2007 A DIVISION OF NSi INDUSTRIES, LLC
33
CATALOG UPC
NO CODE SETTABLE INTERVALS
SSA100 14010 MINUTES: 5, 15, 30 HOURS: 1, 3, 6, 9, 12
SSA200 14011 MINUTES: 10, 20, 40, 60, 90 HOURS: 2, 4, 6, 8
SSA200R-24 14014 MINUTES: 10, 20, 40, 60, 90 HOURS: 2, 4, 6, 8
SPECIFICATIONS & WIRING DIAGRAM:
SSA100, SSA200 SSA100/200
Note: unit is not suitable for lamps which require long striking periods
i.e. HID type.
BLACK HOT
INPUT: Multi-voltage 120/277 VAC, 50/60Hz GREEN 120V GROUND
CONTACT RATINGS: GREEN /YELLOW 277V GROUND
type 120VAC 277VAC
tungsten 800W RED LOAD NEUTRAL
ballast 800W 1200W
motor 1/6HP SSA100/200
pilot duty 240VA
TIMING ACCURACY: .002% BLACK HOT
OPERATING TEMPERATURE: 0 - 100 F OPERATING HUMIDITY: 90% RH Non-condensing GREEN 120V GROUND
GREEN /YELLOW 277V GROUND
COLOR of faceplate and wallplate: white RED (+) 24VAC
WARNING BEFORE TIME OUT: Flicker feature turns load off for 1 second, 2 minutes before end of timed RED or
NEUTRAL
LOAD ()
cycle and again 1 minute before end of timed cycle. BLACK VDC
BEEP FEATURE will sound a 12 second beep every 12 seconds during the last 2 minutes of timed cycle.
ORANGE NC
BLUE C
REMOTE GREY
OVERRIDE NO
YELLOW
RED (+) 24VAC
SPECIFICATIONS & WIRING DIAGRAM: YELLOW or
BLACK () VDC
SSA200R-24
INPUT VOLTAGE: 24VAC / VDC (No Minimum Load) SSA200R-24 ORANGE NC
CURRENT DRAW: 16ma max. @ 24VDC BLUE C
USING TRP TRANSFORMER RELAY POWERPACK 20 AMP
22ma max. @ 24VAC REMOTE GREY
LOAD
CONTACTS: Single Pole, Double Throw OVERRIDE NO L
RED
Isolated Contacts YELLOW
RED
RED
CONTACT RATING: 1 A 30V Maximum YELLOW
BLACK
100A @ 1V Minimum RED
ORANGE NC
TORK
TIMING ACCURACY: .002%
TRP
BLUE BLACK
OPERATING TEMPERATURE: 0- 100 F SSA200R-24 C
REMOTE GREY
OPERATING HUMIDITY: 90% RH Non-condensing USINGOVERRIDE
TRP TRANSFORMER NO
RELAY POWERPACK BLUE 20 AMP
COLOR of faceplate and wallplate: white YELLOW LOAD
WHITE
BLACK
RED L
WARNING BEFORE TIME OUT: Flicker feature turns load YELLOW
RED
RED
LOW
off for 1 second, 2 minutes before end of timed cycle BLACK
VOLTAGE N L
and again 1 minute before end of timed cycle. RED
BEEP FEATURE will sound a 12 second beep every 12 ORANGE NC TORK
TRP
BLUE BLACK
seconds during the last 2 minutes of timed cycle. C
REMOTE GREY
OVERRIDE NO BLUE
YELLOW
WHITE
BLACK
YELLOW LOW
VOLTAGE N L
SPECIFICATION WRITERS GUIDE SSA100, SSA200
Furnish and install a solid state interval time switch with backlit LCD display. Intervals can be preset using a series of dip switches. A tamper resistant manual scroll-up mode must
be provided to override the dip switch setting temporarily. Unit shall be capable of a user selectable audible and/or visual warning beginning 2 minutes prior to time out. Unit
design to provide zero power switching for the contacts. Unit to accept 120/277VAC, 50/60 Hz. A white decorator wallplate to be included.
SPECIFICATION WRITERS GUIDE SSA200R-24
Furnish and install a solid state interval time switch with backlit LCD display. Intervals can be preset using a series of dip switches. A tamper resistant manual scroll-up mode must
be provided to override the dip switch setting temporarily. Unit shall be capable of a user selectable audible and/or visual warning beginning 2 minutes prior to time out. Unit to
accept 24VAC/ DC. A white decorator wallplate to be included.
JUNE 2007 A DIVISION OF NSi INDUSTRIES, LLC
33
